Description

Detail Information

Temp. Range: Environmental Temp ±20℃~+200℃ Heating-up Time: ≤60min Temperature And Humidity Regulating Method: Forced Hot Wind Circulation Ventilation Mode Working Environment Temp.: 0~+40℃ Shell: Double Galvanized Plates,surface Spray Treatment Inner Tanks: Stainless Steel SUS201/8K,mirror Plate High Light:

temperature and humidity chamber

,

climatic test chamber

Product Description

Odor Test Chamber

 

Product purpose

 

High temperature test chamber can be used to test and confirm the odor detection and testing with small sampling bag method of storage and usage of such products as Electrician,electronics,automotive electrical materials,agricultural products and leather under high temp.

 

Feature

 

Accurate control of temp. and wind speed is achieved through advanced controller,among which air circulation system within the chamber controls the direction and flow rate of air flow in the chamber ,while program settings of the control system reaches the function of temp. change and provides the environmental conditions required for odor test automatically.High temp. chamber is sealed with low odor volatile materials of full welded,and its air should be exchanged with clean air outside.

 

 

Reference Standards

 

• GB/T 2423.2-2001 Test B:high temeprature test method

• GJB 150.3-1986 high temperature test

• IEC68-2-2 Test B:dry heat

• GB11158 Techinical conditions of high temperature test chamber

• GB/T2423.2 Basic Environment of Electric and Electronic Products Test

• QJQ 11052-2010 Odor test method for interiors of vehicles

• MS 300-34 Odor test method for interior of vehicles

• GB/T18885-2009 Ecological textile

• QB/T2725-2005 Determination of Leather Odor

• GB18401-2003 Specifications for Basie Safety Technology of National Textile

 

Technical Parameters:

 

Model		V-0V-216	V-0V-768	V-0V-1000	V-0V-4000	V-0V-8000
Volume		216	768	1000	4000	8000
Performance	temp. range	Environmental temp ±20℃~+200℃
	temp. fluctuation	If ≤100℃,0.4℃；≤200℃,0.,8℃
	temp. deviation	If ≤100℃,±1.5℃；≤200℃,±2℃
	heating-up time	Environmental temp ±20℃~+200℃
		≤60min
Internal dimension		600*600*600	830*1200*800	1000*1000*1000	2000*1000*2000	2000*2000*2000
External dimension		800*1200*1295	1030*1800*1495	1730*1480*1275	2700*1800*2750	2700*2400*3200
Temperature and humidity regulating method		Forced hot wind circulation ventilation mode
working environment temp.		0~+40℃
Material	Shell	Double galvanized plates,surface spray treatment
	Inner tanks	stainless steel SUS201/8K,mirror plate
	Heat preservation	glass fibre
	Heater	Ni Cr alloy fin type electric heater
	draught fan	Axial flow fan
	ventilation door	Manual switching(opening degree is adjustable)
Controller	Operation mode	Program operation controller
	setting range	0~+120℃
	setting accuracy	Temp:1℃, time : 1min
	Display resolution	Temp : 0.1℃, time : 1min
	Operating interface	according to the setting mode
	control method	PID+SSR
	Input	K type thermocouple
	Auxillary function	Input disconnection,detection function,uooer limit temperature alarm function,buzzer alarm function,automatic temperature overhet prevention function,abnormal indication,alarm number display.self-diagnosis function and temp. and time keeping function.
Installed capacity(Kw)		6	8	9	15	20
Standard configuration		2 sets of sample holders,1 piece of power line(6 meters long) and 1 set of rubber plug and cap of pin hole
Power		AC380V 3 phases 4 lines + protective earth wire
Mounting device		leakage circuit breaker for the power,overheat protector(upper limit temperature alarm function,fan motor overheat protection switch,control circuit short circuit protection fuse and over temp. protector
Optional		Pin hole(Ω50mm Ω100mm); Rubber plug of pin hold(Ω50mm Ω100mm,cooperative use with pin hole); Sample holder,reinforced inner box and chassis,timer meter and temp. grapher; Emergency stop switch,remote monitoring operation,external alarm output terminal, exhaust flange and stainless steel exhaust elbow
Additional products for optional choice smell box(patented product)		standard odor smell chamber can be provided,uniform smell test can be realized,and accurate control of temperature,relative humidity,wind speed and indoor air cleanliness can be provided.External standard gases can be controlled with micro elements such as solenoid valve(handle valve) and flowmeter,so that the result of smell test can be more stable,accurate,scientific and standardized.

 

Note:

※ When indoor temperature is ±25℃,it will be under circulating operation without test sample conditions or data measured when exchanging air.

※ Fluctuation is indicated according to the rules of GB/T5170.2-1996,it shows ±0.2℃,±0.4℃ or ±0.6℃

※ Excluding the part with convex shape

※ Optional air inlet purifying device,whose height is incresed by 350mm

※ 4 standard configurations of sampling port,with 12 sampling ports optional.

※ can be used for smell test,ordinary high temp. Chamber test and small sampling bag method test.